Blooming Cylinder Necklace
We are adding the craft to your Craft Projects.
The project was added to your Craft Projects.
Friendly plastic in metallic colors of gold, silver and copper accent this lovely necklace with beads and brass flower from AMACO. This is a great way to use all your odd jewelry components in a fun eclectic mix. Get creative and be sure to make a matching pair of earrings.
- Friendly Plastic 7” sticks: Gold/Black, Gold Spectra/Black, Silver/Black, Silver Spectra/Black, Copper/Black
- Matte knife
- Acrylic ruler
- Cutting mat
- Griddle set at 200-300 degrees
- Non stick baking sheet
- Silicone non-stick baking sheet liner, cut to size: 3”x 8 1/2”
- 8” length of 1/8” (4mm) Rubber tubing, sold by the foot at Hobby stores
- Craft blade or utility knife
- Round nose and needle nose jewelry pliers
- Wire cutters
- Needle tool
- Jewelry supplies and findings: (Etsy.com) brass head pins, 6” piece wire, chain, clasp, spacer beads, crystal rondell, brass flower, crystal bead, fresh water pearl, branch pearl and jump rings.
- Using a cutting mat, ruler and blade, cut a 1/4” and 1/8” strip from each color of plastic stick. Then cut the strips in half using a scissor.
- Pre heat the griddle. Place the baking sheet onto the griddle. One at a time, in a pleasing color pattern. Place the plastic strips onto the baking sheet. Make sure each strip is stuck in place before adding the next. Try to press each strip tightly against the one before, to prevent any gaps. Continue until the desired number of the strips has been added.
- Allow the plastic to soften and fuse together. If any gaps do appear, simply tap over them with your finger pressing the softened plastic together. When all the strips have softened and sealed together, remove the baking sheet from the griddle and allow the plastic to cool. Use the needle tool to press under the edges of the cooled plastic and remove it from the pan.
- Place the cooled plastic back on the cutting mat and trim off the uneven edges. Cut the plastic into 1” wide strips.
- Lay the silicone sheet onto the griddle. Position the plastic strip, right side down onto the center of the silicone sheet and allow the plastic to soften. You will notice as the plastic softens it becomes very shiny. It is important that you watch this process closely. As soon as the entire strip is shiny, remove the silicone sheet from the heat and lay it onto your counter or work surface.
- Carefully lay the rubber tubing along the top edge of the softened plastic strip.
- Moisten your fingers and hands with water, to prevent sticking to the plastic, and begin to roll it up and around the tubing. Continue until all of the plastic is wrapped around the tubing. Now you can use your fingers and palms of your hands to roll the cylinder back and forth on the silicone sheet, to secure and seal the overlap. Once you are happy with the look of your cylinder, pick it up by the extended ends of the tubing, pulling it straight and taunt. Quickly run it under the flow of cold water from the faucet. This will quickly harden the outside of the cylinder allowing you to lay it down, to finish the cooling process without the fear of it getting marred.
- Once the cylinder has cooled and the plastic has hardened completely, remove the rubber tubing by pulling on each of the exposed ends until the seal within the cylinder has been broken. You will know when this has happened, as the tubing will slide out.
- Place the cylinder onto the cutting mat and trim off the uneven ends, using a craft blade or a utility knife. I prefer using the craft blade for this. You do need to put a little muscle behind it in order to cut through the plastic. Just do it carefully. Continue to cut the cylinder into 1” beads.
- Assemble all the decorative components, and begin sliding them onto the wire in a pleasing arrangement. You may want to add the pearl, flower and crystal to a small length of chain first. Use the photo above as a guide or create your own arrangement. Once you are satisfied with the arrangement form a loop using round nose pliers to both ends of the wire.
- Attach the decorative cylinder to the chain using jump rings. Finish the necklace by attaching the jump ring and clasp.
Variation: This is a great way to use all your odd jewelry components in a fun eclectic mix. Get creative and be sure to make a matching pair of earrings.
Free projects, giveaways, exclusive partner offers, and more straight to your inbox!
Your Recently Viewed Projects
Images from other crafters
Report Inappropriate Comment
Are you sure you would like to report this comment? It will be flagged for our moderators to take action.
Thank you for taking the time to improve the content on our site.
- How to Make Shrink Plastic Jewelry
- DIY Shrinky Dinks: A Shrink Plastic Craft Guide
- Are Shrinky Dinks Safe?
- Eagle Divers Friendship Bracelets
- Spirit of the Heart Necklace
- Brightly Colored Bangles
- Shrink Plastic Charms Project
- Out of Asia
- Triangle Brass and Friendly Plastic Pendant
- Shrink Plastic Name Necklace
Our Newest Projects & Articles
- Simple Spa Slippers
- Lovely Victorian Lace Heart ❤️ Ornament
- Rose Milk Bath Tea
- How To Make A Sherpa Fleece And Flannel Blanket
- Heart Block Pillow Pattern
- Wax Air Freshener With Dried Flowers
- Diy Bird Feeders
- Winter Rays Hat
- Chunky Heart Pillow
- How To Miter Corners
- 11 Crochet Shawl Patterns: Crochet Poncho Patterns, Free Easy Crochet Patterns and More
- 12 Knitted Scarf Patterns: Fabulous Free Knitting Patterns for Beginners
- 14 Free Crochet Patterns for Babies and Toddlers
- 16 Free Crochet Hat Patterns, Scarves, and Gloves
- 22 Free Crochet Patterns: Afghan Patterns, Crochet Hats, and More
- 24 Quick and Easy Knitting Patterns
- 7 Adult Coloring Pages
- 8 Free Apron Sewing Patterns
- Easy Lace Knitting Patterns
- Quick & Easy Decoupage: 12 Fabulous Mod Podge Projects for Your Home